Reflectors

Carley Lamps manufactures Aluminum Reflectors, Set Screw Reflector, and Lamp Sleeves/Reflector Sleeves designed to fit Carley's Set Screw Assemblies.

Carley Lamps manufactures parabolic and elliptical reflectors ranging from .25 inches to 3.00 inches in diameter. Carley Lamps can produce reflectors up to 6.0" in diameter, as well as offer several coatings and textures on the reflector face. Carley refectors are hand polished, and vacuum metallized coated when required. Hand polishing reflectors forms a fine coating of aluminum oxide on the reflector face and this protects the reflector, maintaining its bright surface. Carley Aluminum reflectors are excellent at absorbing heat and they hold up against high wattage lamps better than plastic reflectors. Carley aluminum reflectors are excellent at reflecting, collimating and refocusing both visible, ultra violet and Infra Red Light. Contact Carley Lamps today for assistance in choosing the best performing reflector for your application.

* Par = Parabolic (Collimating) Ell = Elliptical (Refocusing).
** Optimum Refocus - refocus can be changed by moving lamp forward or backward inside the reflector

NOTE: By locating the lamp filament at the "focal point," you will obtain maximum performance. Securing the lamp to a standard reflector is normally accomplished by gluing the lamp into the reflector. For greater options and ease of use, review the Set Screw Reflectors.

Parabolic Set Screw Reflectors	Elliptical Set Screw Reflectors
Material Aluminum - Machined and Polished**	Material Aluminum - Machined and Polished**
Parabolic 2 and 3 Inch Set Screw Reflectors	Elliptical 2 and 3 Inch Set Screw Reflectors
Material Aluminum - Machined and Polished**	Material Aluminum - Machined and Polished**

Set Screw Reflectors Carley Set Screw Reflectores are identical to our standard Aluminum reflectors except that they allow the customer to adjust the position of the lamp inside the reflector as often as desired. Another benefit of the set screw reflectors is that when a lamp burns out, only the lamp and lamp sleeve need to be replaced as the set screw reflector will last for years under normal conditions. When working with a Set Screw Reflector, be sure that your light bulb has a protective metal sleeve around it. Click here for Lamp Sleeves. REFLECTOR TYPE* DIA. O.L. REAM REFOCUS** FOCAL FOR LAMP 1925 Ell .375 .50 .189 .18 0 T-1 1932 Par .375 .50 .189 0 .05 T-1 1926 Ell .375 .50 .252 .18 0 T-1 1/2 1933 Par .375 .50 .252 0 .05 T-1 1/2 1927 Ell .500 .50 .189 .22 0 T-1 1934 Par .500 .50 .189 0 .07 T-1 1928 Ell .500 .50 .252 .22 0 T-1 1/2 1935 Par .500 .50 .252 0 .07 T-1 1/2 1929 Ell .750 .75 .252 .37 0 T-1 1/2 1936 Par .750 .75 .252 0 .10 T-1 1/2 1930 Ell .750 .75 .377 .37 0 T-2 1/2 1937 Par .750 .75 .377 0 .10 T-2 1/2 1931 Ell 1.00 1.00 .377 .49 0 T-2 1/2 1938 Par 1.00 1.00 .377 0 .12 T-2 1/2 1939 Par 1.37 1.00 .377 0 .16 T-2 1/2 1940 Par 2.00 1.30 .377 0 .20 T-2 1/2 2128 Ell 2.00 1.30 .377 1.00 0 T-2 1/2 2102 Par 3.00 2.50 .377 0 .24 T-2 1/2 2104 Ell 3.00 2.50 .377 1.20 0 T-2 1/2 * Par = Parabolic (Collimating) Ell = Elliptical (Refocusing). ** Optimum Refocus - refocus can be changed by moving lamp forward or backward inside the reflector Parabolic Set Screw Reflectors Elliptical Set Screw Reflectors Material Aluminum - Machined and Polished** Material Aluminum - Machined and Polished** Parabolic 2 and 3 Inch Set Screw Reflectors Elliptical 2 and 3 Inch Set Screw Reflectors Material Aluminum - Machined and Polished** Material Aluminum -Machined and Polished** **These reflectors can also be vacuum metallized after polishing, for increased reflectance - there is an additional charge for vacuum metallizing. Lamp Sleeves/Reflector Sleeves The assemblies shown below are designed to fit Carley's Set Screw Reflector Assemblies. Carley lamps size T-1, T-1 ½ and T-2 ½ can be used in any size reflector we offer. Be careful to order the correct sleeve for the lamp and reflector combination you will be combining. NOTE: Use sleeve 2129 for T-1 ½ lamp to obtain T-2 ½ OD sleeve diameter. Use sleeve 2138 for T-2 ½ lamp in 3 inch diameter reflector.

This page is OK as of 09 Nov. 05